Miri Korenblit says:
====================
iwlwifi-fixes
- missing unlock in error path
- Avoid FW assert on bad command values
- fix kernel panic due to incorrect index calculation
====================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When running in AP mode and deauthenticating a client that's in powersave
mode, the disassoc/deauth packet can get stuck in a tx queue along with
other buffered frames. This can fill up hardware queues with frames
that are only released after the WTBL slot is reused for another client.
Fix this by moving deauth packets to the ALTX queue.
Reported-by: Chad Monroe <chad.monroe@adtran.com>
Link: https://patch.msgid.link/20250707154702.1726-2-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Several places use rcu_dereference to get a wcid entry without validating
if the index exceeds the array boundary. Fix this by using a helper function,
which handles validation.
Link: https://patch.msgid.link/20250707154702.1726-1-nbd@nbd.name
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The decap offload configuration should only be applied after the STA has
been successfully initialized. Attempting to configure it earlier can lead
to corruption of the MAC configuration in the chip's hardware state.
Add an early check for `msta->deflink.wcid.sta` to ensure the station peer
is properly initialized before proceeding with decapsulation offload
configuration.
Cc: stable@vger.kernel.org
Fixes: 24299fc869 ("mt76: mt7921: enable rx header traslation offload")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Link: https://patch.msgid.link/f23a72ba7a3c1ad38ba9e13bb54ef21d6ef44ffb.1748149855.git.deren.wu@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since mt76_mcu_skb_send_msg() routine can't be executed in atomic context,
move RCU section in mt7996_mcu_add_rate_ctrl() and execute
mt76_mcu_skb_send_msg() in non-atomic context. This is a preliminary
patch to fix a 'sleep while atomic' issue in mt7996_mac_sta_rc_work().
Fixes: 0762bdd302 ("wifi: mt76: mt7996: rework mt7996_mac_sta_rc_work to support MLO")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250605-mt7996-sleep-while-atomic-v1-4-d46d15f9203c@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since mt7996_mcu_set_fixed_field() can't be executed in a RCU critical
section, move RCU section in mt7996_mcu_add_rate_ctrl_fixed() and run
mt7996_mcu_set_fixed_field() in non-atomic context. This is a
preliminary patch to fix a 'sleep while atomic' issue in
mt7996_mac_sta_rc_work().
Fixes: 0762bdd302 ("wifi: mt76: mt7996: rework mt7996_mac_sta_rc_work to support MLO")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250605-mt7996-sleep-while-atomic-v1-3-d46d15f9203c@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since mt76_mcu_skb_send_msg() routine can't be executed in atomic context,
move RCU section in mt7996_mcu_set_fixed_field() and execute
mt76_mcu_skb_send_msg() in non-atomic context. This is a preliminary
patch to fix a 'sleep while atomic' issue in mt7996_mac_sta_rc_work().
Fixes: 0762bdd302 ("wifi: mt76: mt7996: rework mt7996_mac_sta_rc_work to support MLO")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://patch.msgid.link/20250605-mt7996-sleep-while-atomic-v1-2-d46d15f9203c@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There is a potential NULL pointer dereference in zd_mac_tx_to_dev(). For
example, the following is possible:
T0 T1
zd_mac_tx_to_dev()
/* len == skb_queue_len(q) */
while (len > ZD_MAC_MAX_ACK_WAITERS) {
filter_ack()
spin_lock_irqsave(&q->lock, flags);
/* position == skb_queue_len(q) */
for (i=1; i<position; i++)
skb = __skb_dequeue(q)
if (mac->type == NL80211_IFTYPE_AP)
skb = __skb_dequeue(q);
spin_unlock_irqrestore(&q->lock, flags);
skb_dequeue() -> NULL
Since there is a small gap between checking skb queue length and skb being
unconditionally dequeued in zd_mac_tx_to_dev(), skb_dequeue() can return NULL.
Then the pointer is passed to zd_mac_tx_status() where it is dereferenced.
In order to avoid potential NULL pointer dereference due to situations like
above, check if skb is not NULL before passing it to zd_mac_tx_status().
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 459c51ad6e ("zd1211rw: port to mac80211")
Signed-off-by: Daniil Dulov <d.dulov@aladdin.ru>
Link: https://patch.msgid.link/20250626114619.172631-1-d.dulov@aladdin.ru
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Miri Korenblit says:
====================
iwlwifi-fixes: fix failure in interface up
====================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Unfortunately, FWs of some devices don't have the version of the
iwl_mac_config_cmd defined in the TLVs. We send 0 as the 'def argument
to iwl_fw_lookup_cmd_ver, so for such FWs, the return value will be 0,
leading to a warning, and to not sending the command.
Fix this by assuming that the default version is 1.
Fixes: 83f3ac2848 ("wifi: iwlwifi: Fix incorrect logic on cmd_ver range checking")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250624071427.2662621-1-miriam.rachel.korenblit@intel.com
In some rare randconfig builds, I seem to trigger a bug in clang where
it unrolls a loop but then runs out of registers, which then get
spilled to the stack:
net/wireless/intel/iwlegacy/4965-rs.c:2262:1: error: stack frame size (1696) exceeds limit (1280) in 'il4965_rs_rate_init' [-Werror,-Wframe-larger-than]
This seems to be the same one I saw in the omapdrm driver, and there is
an easy workaround by not inlining the il4965_rs_rate_scale_clear_win
function.
Link: https://github.com/llvm/llvm-project/issues/143908
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Link: https://patch.msgid.link/20250620113946.3987160-1-arnd@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
on arm64 defconfig build failed with gcc-8:
drivers/net/wireless/intel/iwlwifi/pcie/ctxt-info.c:208:3:
include/linux/bitfield.h:195:3: error: call to '__field_overflow'
declared with attribute error: value doesn't fit into mask
__field_overflow(); \
^~~~~~~~~~~~~~~~~~
include/linux/bitfield.h:215:2: note: in expansion of macro '____MAKE_OP'
____MAKE_OP(u##size,u##size,,)
^~~~~~~~~~~
include/linux/bitfield.h:218:1: note: in expansion of macro '__MAKE_OP'
__MAKE_OP(32)
Limit cb_size to valid range to fix it.
Signed-off-by: Pei Xiao <xiaopei01@kylinos.cn>
Link: https://patch.msgid.link/7b373a4426070d50b5afb3269fd116c18ce3aea8.1748332709.git.xiaopei01@kylinos.cn
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
The initialization of async_handlers_list
was accidentally removed in a previous change.
Then it was restoted by commit 175e69e33c ("wifi: iwlwifi: restore
missing initialization of async_handlers_list").
Somehow, the initialization disappeared again.
Restote it.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Jeff Johnson says:
==================
ath.git updates for v6.16-rc3
Fix the following 3 issues:
wifi: ath12k: avoid burning CPU while waiting for firmware stats
wifi: ath12k: don't activate more links than firmware supports
wifi: carl9170: do not ping device which has failed to load firmware
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For WMI_REQUEST_VDEV_STAT request, firmware might split response into
multiple events dut to buffer limit, hence currently in
ath12k_wmi_fw_stats_process() host waits until all events received. In
case there is no vdev started, this results in that below condition
would never get satisfied
((++ar->fw_stats.num_vdev_recvd) == total_vdevs_started)
consequently the requestor would be blocked until time out.
The same applies to WMI_REQUEST_BCN_STAT request as well due to:
((++ar->fw_stats.num_bcn_recvd) == ar->num_started_vdevs)
Change to check the number of started vdev first: if it is zero, finish
directly; if not, follow the old way.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Fixes: e367c92476 ("wifi: ath12k: Request vdev stats from firmware")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250612-ath12k-fw-fixes-v1-4-12f594f3b857@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently ath12k_wmi_fw_stats_process() is using static variables to count
firmware stat events. Taking num_vdev as an example, if for whatever
reason (say ar->num_started_vdevs is 0 or firmware bug etc.) the following
condition
(++num_vdev) == total_vdevs_started
is not met, is_end is not set thus num_vdev won't be cleared. Next time
when firmware stats is requested again, even if everything is working
fine, failure is expected due to the condition above will never be
satisfied.
The same applies to num_bcn as well.
Change to use non-static counters and reset them each time before firmware
stats is requested.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Fixes: e367c92476 ("wifi: ath12k: Request vdev stats from firmware")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250612-ath12k-fw-fixes-v1-3-12f594f3b857@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Regarding the firmware stats events handling, the comment in
ath12k_mac_get_fw_stats() says host determines whether all events have been
received based on 'end' tag in TLV. This is wrong as there is no such tag
at all, actually host makes the decision totally by itself based on the
stats type and active pdev/vdev counts etc.
Fix it to correctly reflect the logic.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250612-ath12k-fw-fixes-v1-1-12f594f3b857@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In case of ML connection, currently all useful links are activated at
ASSOC stage:
ieee80211_set_active_links(vif, ieee80211_vif_usable_links(vif))
this results in firmware crash when the number of links activated on the
same device is more than supported.
Since firmware supports activating at most 2 links for a ML connection,
to avoid firmware crash, host needs to select 2 links out of the useful
links. As the assoc link has already been chosen, the question becomes
how to determine partner links. A straightforward principle applied
here is that the resulted combination should achieve the best throughput.
For that purpose, ideally various factors like bandwidth, RSSI etc should
be considered. But that would be too complicate. To make it easy, the
choice is to only take hardware modes into consideration.
The SBS (single band simultaneously) mode frequency range covers 5 GHz
and 6 GHz bands. In this mode, the two individual MACs are both active,
with one working on 5g-high band and the other on 5g-low band (from
hardware perspective 5 GHz and 6 GHz bands are referred to as a 'large'
single 5 GHz band). The DBS (dual band simultaneously) mode covers 2 GHz
band and the 'large' 5 GHz band, with one MAC working on 2 GHz band and
the other working on 5 GHz band or 6 GHz band. Since 5,6 GHz bands could
provide higher bandwidth than 2 GHz band, the preference is given to SBS
mode. Other hardware modes results in only one working MAC at any given
time, so it is chosen only when both SBS are DBS are not possible.
For each hardware mode, if there are more than one partner candidate,
just choose the first one.
For now only single device MLO case is handled as it is easy. Other cases
could be addressed in the future.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-6-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In case of two links established on the same device in an ML connection,
depending on device's hardware mode capability, it is possible that both
links fall on the same MAC. Currently, no specific action is taken to
address this but just keep both links active. However this would result
in lower throughput compared to even one link, because switching between
these two links on the resulted MAC significantly impacts throughput.
Check if both links fall in the frequency range of a single MAC. If
so, send WMI_MLO_LINK_SET_ACTIVE_CMDID command to firmware such that
firmware can deactivate one of them. Note the decision of which link
getting deactivated is made by firmware, host only sends the vdev
lists.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-5-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Previous patches parse and save hardware MAC frequency range information
in ath12k_svc_ext_info structure. Such range represents hardware
capability hence needs to be updated based on host information, e.g. guard
the range based on host's low/high boundary.
So update frequency range. The updated range is saved in
ath12k_hw_mode_info structure and would be used when doing vdev activation
and link selection in following patches.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-3-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Firmware sends the boundary between lower and higher bands in
ath12k_wmi_dbs_or_sbs_cap_params structure embedded in
WMI_SERVICE_READY_EXT2_EVENTID event. The boundary is needed when
updating frequency range in the following patch. So parse and save
it for later use. Note ath12k_wmi_dbs_or_sbs_cap_params is placed
after some other structures, so placeholders for them are added
as well.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-2-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
WLAN hardware might support various hardware modes such as DBS (dual
band simultaneously), SBS (single band simultaneously) and DBS_OR_SBS
etc, see enum wmi_host_hw_mode_config_type. Firmware advertises actual
supported modes in WMI_SERVICE_READY_EXT_EVENTID event. For each mode,
firmware advertises frequency range each hardware MAC can operate on.
In MLO case such information is necessary during vdev activation and
link selection (which is done in following patches), so add a new
structure ath12k_svc_ext_info to ath12k_wmi_base, then parse and save
those information to it for later use.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-1-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When the ath12k driver is built without CONFIG_ATH12K_DEBUG, the
recently refactored stats code can cause any user space application
(such at NetworkManager) to consume 100% CPU for 3 seconds, every time
stats are read.
Commit 'b8a0d83fe4c7 ("wifi: ath12k: move firmware stats out of
debugfs")' moved ath12k_debugfs_fw_stats_request() out of debugfs, by
merging the additional logic into ath12k_mac_get_fw_stats().
Among the added responsibility of ath12k_mac_get_fw_stats() was the
busy-wait for `fw_stats_done`.
Signalling of `fw_stats_done` happens when one of the
WMI_REQUEST_PDEV_STAT, WMI_REQUEST_VDEV_STAT, and WMI_REQUEST_BCN_STAT
messages are received, but the handling of the latter two commands remained
in the debugfs code. As `fw_stats_done` isn't signalled, the calling
processes will spin until the timeout (3 seconds) is reached.
Moving the handling of these two additional responses out of debugfs
resolves the issue.
Fixes: b8a0d83fe4 ("wifi: ath12k: move firmware stats out of debugfs")
Signed-off-by: Bjorn Andersson <bjorn.andersson@oss.qualcomm.com>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://patch.msgid.link/20250609-ath12k-fw-stats-done-v1-1-2b3624656697@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth and wireless.
Current release - regressions:
- af_unix: allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD
Current release - new code bugs:
- eth: airoha: correct enable mask for RX queues 16-31
- veth: prevent NULL pointer dereference in veth_xdp_rcv when peer
disappears under traffic
- ipv6: move fib6_config_validate() to ip6_route_add(), prevent
invalid routes
Previous releases - regressions:
- phy: phy_caps: don't skip better duplex match on non-exact match
- dsa: b53: fix untagged traffic sent via cpu tagged with VID 0
- Revert "wifi: mwifiex: Fix HT40 bandwidth issue.", it caused
transient packet loss, exact reason not fully understood, yet
Previous releases - always broken:
- net: clear the dst when BPF is changing skb protocol (IPv4 <> IPv6)
- sched: sfq: fix a potential crash on gso_skb handling
- Bluetooth: intel: improve rx buffer posting to avoid causing issues
in the firmware
- eth: intel: i40e: make reset handling robust against multiple
requests
- eth: mlx5: ensure FW pages are always allocated on the local NUMA
node, even when device is configure to 'serve' another node
- wifi: ath12k: fix GCC_GCC_PCIE_HOT_RST definition for WCN7850,
prevent kernel crashes
- wifi: ath11k: avoid burning CPU in ath11k_debugfs_fw_stats_request()
for 3 sec if fw_stats_done is not set"
* tag 'net-6.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (70 commits)
selftests: drv-net: rss_ctx: Add test for ntuple rules targeting default RSS context
net: ethtool: Don't check if RSS context exists in case of context 0
af_unix: Allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD.
ipv6: Move fib6_config_validate() to ip6_route_add().
net: drv: netdevsim: don't napi_complete() from netpoll
net/mlx5: HWS, Add error checking to hws_bwc_rule_complex_hash_node_get()
veth: prevent NULL pointer dereference in veth_xdp_rcv
net_sched: remove qdisc_tree_flush_backlog()
net_sched: ets: fix a race in ets_qdisc_change()
net_sched: tbf: fix a race in tbf_change()
net_sched: red: fix a race in __red_change()
net_sched: prio: fix a race in prio_tune()
net_sched: sch_sfq: reject invalid perturb period
net: phy: phy_caps: Don't skip better duplex macth on non-exact match
MAINTAINERS: Update Kuniyuki Iwashima's email address.
selftests: net: add test case for NAT46 looping back dst
net: clear the dst when changing skb protocol
net/mlx5e: Fix number of lanes to UNKNOWN when using data_rate_oper
net/mlx5e: Fix leak of Geneve TLV option object
net/mlx5: HWS, make sure the uplink is the last destination
...
Jeff Johnson says:
==================
ath.git updates for v6.16-rc2
Fix a handful of both build and stability issues across multiple drivers.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the execution of ath12k_core_hw_group_assign() or
ath12k_core_hw_group_create() fails, the registered notifier chain is not
unregistered properly. Its memory is freed after rmmod, which may trigger
to a use-after-free (UAF) issue if there is a subsequent access to this
notifier chain.
Fixes the issue by calling ath12k_core_panic_notifier_unregister() in
failure cases.
Call trace:
notifier_chain_register+0x4c/0x1f0 (P)
atomic_notifier_chain_register+0x38/0x68
ath12k_core_init+0x50/0x4e8 [ath12k]
ath12k_pci_probe+0x5f8/0xc28 [ath12k]
pci_device_probe+0xbc/0x1a8
really_probe+0xc8/0x3a0
__driver_probe_device+0x84/0x1b0
driver_probe_device+0x44/0x130
__driver_attach+0xcc/0x208
bus_for_each_dev+0x84/0x100
driver_attach+0x2c/0x40
bus_add_driver+0x130/0x260
driver_register+0x70/0x138
__pci_register_driver+0x68/0x80
ath12k_pci_init+0x30/0x68 [ath12k]
ath12k_init+0x28/0x78 [ath12k]
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 6f245ea0ec ("wifi: ath12k: introduce device group abstraction")
Signed-off-by: Miaoqing Pan <miaoqing.pan@oss.qualcomm.com>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250604055250.1228501-1-miaoqing.pan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
